1,8Nm 3 Achsen Schrittmotor Set parallel :
3 Stk. Schrittmotor 1,8Nm. Artikelnr. 100-100-110
3 Stk. Schrittmotor Endstufe DM542 Artikelnr. 100-300-120
1 Stk.4 Kanal Parallelport Interface Artikelnr. 100-400-102
1 Stk. Schaltnetzteil 320VA 48VDC Artikelnr. 300-600-140
Sie sparen 17,21 Euro
Technische Details 1,8Nm 3 Achsen Schrittmotor Set parallel
Technische Daten 1,8 Nm Schrittmotor:
|
|
|
Unipolar |
Bipolar Seriel |
Bipolar Parallel |
Schrittwinkel |
Grad |
1,8 |
|
|
|
Motor Länge |
mm |
76,6 |
|
|
|
Spannung |
Volt |
|
3 |
4,2 |
2,1 |
Strom |
Ampere |
|
3 |
2,1 |
4,2 |
Phasen Widerstand |
Ohm |
|
1 |
2 |
0,5 |
Phasen Induktivität |
mh |
|
1,5 |
6 |
1,5 |
Haltemoment |
Nm |
|
1,45 |
1,8 |
1,8 |
Rastmoment |
Ncm |
|
|
|
|
Rotor Trägheitsmoment |
Kg*cm² |
0,48 |
|
|
|
Adernzahl |
Stück |
8 |
|
|
|
Gewicht |
Kg |
1,5 |
|
|
|
Wellendurchmesser 1 |
mm |
8 |
|
|
|
Wellendurchmesser 2 |
mm |
|
|
|
|
Isolationsklasse |
|
B |
|
|
|
Introduction:
DM542 is a type of two-phase hybrid stepping motor driver, The drive voltage of which is from 24VDC to 50VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 42mm to 86mm outside diameter and less than 4.0A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Hording torque when DQ542MA run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, Computer embroider machine, packing machines and so on.
Features:
- High performance, low price
- Average current control, 2-phase sinusoidal output current drive
- Supply voltage from 24VDC to 50VDC
- Opto-isolated signal I/O
- Overvoltage, under voltage, overcorrect, phase short circuit protection
- 15 channels subdivision and automatic idle-current reduction
- 8 channels output phase current setting
- Offline command input terminal
- Motor torque is related with speed, but not related with step/revolution
- High start speed
- High hording torque under high speed
Electrical specification:
Input voltage |
24-50VDC |
Input current |
< 4A |
Output current |
1.0A~4.2A |
Consumption |
Consumption:80W; Internal Insurance:6A |
Temperature |
Working Temperature -10~45℃;
Stocking temperature -40℃~70℃ |
Humidity |
Not condensation, no water droplets |
gas |
Prohibition of combustible gases and conductive dust |
weight |
200G |
Technische Details Parallelport Interface Ausstattungsmerkmale:
• Interface zum Anschluß von bis zu 4 Takt/Richtungs Endstufen an den PC-Parallelport.
• Alle Signale auf Schraubklemmen geführt, zusätzlich 10-polige Flachbandkabelanschlüsse .
• Verstärkung aller Signale vom Parallelport. Ideal für Endstufen mit Optokoppler-Eingängen, die einen hohen Strombedarf haben.
• Endstufen-Signale auf open-collector Ausgängen, Ausgangsspannung bis 24V, interne Pullups nach +5V.
• Endschalter-Eingänge wahlweise für 5V, oder 12V-Pegel, kompatibel zu Initiatoren (wahlweise NPN oder PNP, aber nicht gemischt verwendbar).
• Schutz des Parallelports durch Begrenzung der Portströme auf max. 10mA/Pin (bei Spannungen bis 50V).
• Charge-Pump Safty Signal: Freigabe der Relais und Endstufen nur, wenn die PC-Software gestartet ist.
• Analoges Ausgangssignal für Drehzahlsteuerung der Hauptspindel (Eingangssignal PWM oder frequenzvariabel)
• Viele Konfigurationsmöglichkeiten (z.B. Pinzuordnung) über Jumper
• 2 Relais für Schaltfunktionen
• Schaltregler für 12V/0,5A (für Lüfter und Relais, erzeugt aus der Motorspannung der Endstufen), 5V/0,5A für den Logikteil
• Platinenformat: Europakarte (160*100mm)
Lieferumfang:
• Bestückte und getestete Karte
• Dokumentation
Technische Daten Schaltnetzteil RSP320-48
• geschlossene Bauform (case) mit Lüfter, Schraubanschlüsse
• Universaleingang
• Überlastschutz durch Abschalten, auto recovery
• geschützt gegen Kurzschluss, Überlast, Überspannung
• eingebauter PFC-Schaltkreis
• niedrige Bauhöhe |
 |
 |
|
|
Eingangsspannungsbereich: |
88...264V AC (47...63Hz) |
124...370V DC |
Einschaltstoßstrom, max.: |
40A |
Leckstrom, max.: |
1mA |
Ausgangsspannungsjustierung: |
±10% |
Überlastschutz: |
105...135% |
Isolationsspannung |
I/P-O/P: |
3000V AC |
I/P-FG: |
2000V AC |
O/P-FG: |
500V AC |
Betriebstemperaturbereich: |
-30...+70°C |
Gewicht: |
900g |
I/P = Eingang (Input), O/P = Ausgang (Output), FG = Masseanschluss |
Artikel |
UA |
IA |
PA |
DUA |
URN |
h |
|
[V] |
[A] |
[W] |
[%] |
[mVp-p] |
[%] |
RSP-320-12 |
12 |
0...26,7 |
320,4 |
1 |
150 |
88 |
RSP-320-13.5 |
13,5 |
0...23,8 |
321,3 |
1 |
150 |
88 |
RSP-320-15 |
15 |
0...21,4 |
321 |
1 |
150 |
88,5 |
RSP-320-24 |
24 |
0...13,4 |
321,6 |
1 |
150 |
89 |
RSP-320-27 |
27 |
0...11,9 |
321,3 |
1 |
200 |
89 |
RSP-320-36 |
36 |
0...8,9 |
320,4 |
1 |
220 |
89,5 |
RSP-320-48 |
48 |
0...6,7 |
321,6 |
1 |
240 |
90 |
UA = Ausgangsspannung, IA = Ausgangsstrombereich, PA = Ausgangsleistung, DUA = Ausgangsspannungstoleranz, URN = Restwelligkeit, h = Wirkungsgrad |